Infotraining Indonesia | Pusat Informasi Pelatihan dan Training di Indonesia PELATIHAN TROUBLESHOOTING, MAINTENANCE & PROTECTION OF AC ELECTRICAL MOTORS & DRIVES | Informasi Training di Indonesia
PELATIHAN TROUBLESHOOTING, MAINTENANCE & PROTECTION OF AC ELECTRICAL MOTORS & DRIVES

PELATIHAN TROUBLESHOOTING, MAINTENANCE & PROTECTION OF AC ELECTRICAL MOTORS & DRIVES

Mar 22, 2018 / By : / Category : Pembangkit Listrik, Telekomunikasi & IT, Training Based Industry, Training Profesional, Training Softskill

PELATIHAN TROUBLESHOOTING, MAINTENANCE & PROTECTION OF AC ELECTRICAL MOTORS & DRIVES

PELATIHAN TROUBLESHOOTING, MAINTENANCE & PROTECTION OF AC ELECTRICAL MOTORS & DRIVES

TRAINING TENTANG TROUBLESHOOTING, MAINTENANCE & PROTECTION OF AC ELECTRICAL MOTORS & DRIVES

DESKRIPSI PELATIHAN TROUBLESHOOTING, MAINTENANCE & PROTECTION OF AC ELECTRICAL MOTORS & DRIVES

It is estimated that electrical drives and other rotating equipment consume about 50% of the total electrical energy consumed in the world today. The cost of maintaining electrical motors can be a significant amount in the budget item of manufacturing and mining industries. This workshop gives you a thorough understanding of electrical motor’s working, maintenance and failure modes and gives you the tools to maintain and troubleshoot electrical motors. You will gain valuable insight into the selection of the protection necessary to ensure your motors are protected against fault conditions, so as to ensure reliability and long life.
You will gain a fundamental understanding of the installation, operation and troubleshooting of electric motors. Typical applications of electric motors in mining, manufacturing, materials handling and process control are covered in detail. You will learn the basic steps in specifying, installing, wiring and commissioning motors. The concluding section of the course gives you the fundamental tools in troubleshooting motors confidently and effectively.

MATERI PELATIHAN TROUBLESHOOTING, MAINTENANCE & PROTECTION OF AC ELECTRICAL MOTORS & DRIVES

INTRODUCTION AND OUTLINE OF WORKSHOP OBJECTIVES
FUNDAMENTALS OF MOTOR TECHNOLOGY
* Basic principles of rotating electric machines
* Fundamental principles of speed control
* Efficiency, torque, inertia, horsepower/power factor
* Torque-speed curves
* How the motor produces torque
* Types of motors

AC MOTOR THEORY, CONSTRUCTION AND MAINTENANCE
* Basic construction and physical configuration, windings
* Principles of operation and performance

THREE PHASE AC INDUCTION MOTORS
* Components
* Theory of operation
* Induction motor design
* Duty cycles
* Insulation and Cooling requirements
* Starting methods
* Selecting motors
* Maintenance of AC machines
* Types of faults, fault finding and testing of AC machines
* Testing instrumentation

PROTECTION OF AC MOTORS
* Protective devices

1. Thermal Overload
2. Over Current / Overload
3. Under-voltage / Over-voltage
4. Under frequency
5. Current unbalance or negative phase sequence
6. Earth fault protection
7. Pole slip / Out of step
8. Loss of excitation
9. Over fluxing
10. Stall protection / acceleration time / Start up supervision (Time between starts / Starts per hour)
11. Voltage controlled or restrained over current

* Protection settings

SPEED CONTROL OF AC MOTORS
* Introduction to Variable Speed Drives or Power Electronic Converters
* Types, and Designs of Variable Speed Drives

PROTECTION OF AC CONVERTORS AND MOTORS
* Frequency converter protection circuits
* Protection settings

CONTROL SYSTEMS FOR AC VARIABLE SPEED DRIVES
* Control theory of VSDs explained

THE SELECTION OF AC CONVERTORS FOR VARIABLE SPEED DRIVE APPLICATIONS
* Selection procedure
* Nature of the load
* Selection of correct size motor and converter

INSTALLATION AND COMMISSIONING OF AC VARIABLE SPEED DRIVES
* General Installation and environmental requirements
* Electrical connections and Earthing requirements
* Control wiring and pre-commissioning
* Commissioning tests

NEW TECHNOLOGIES AND DEVELOPMENTS

METODE

Presentasi, Diskusi, Simulasi, Studi kasus, Evaluasi

Peserta
Staf, Supervisor dan Manajer bagian perawatan dan pemeliharaan, bagian Produksi, Perencanaan dll.

PEMATERI

Ir. Teguh Santoso and Team

 

Jadwal Pelatihan  :

 

  • 15 – 17 Januari 2019
  • 12 – 14 Februari 2019
  • 12 – 14 Maret 2019
  • 9 – 11 April 2019
  • 7 – 9 Mei 2019
  • 18 – 20 Juni 2019
  • 9 – 11 Juli 2019
  • 6 – 8 Agustus 2019
  • 3 – 5 September 2019
  • 24 – 26 September 2019
  • 8 – 10 Oktober 2019
  • 22 – 24 Oktober 2019
  • 5 – 7  November 2019
  • 3 – 5  Desember 2019

 

Jadwal tersebut dapat disesuaikan dengan kebutuhan peserta pelatihan.

 

Lokasi Pelatihan:

 

  • Yogyakarta, Hotel Dafam Malioboro (6.000.000 IDR / participant)
  • Jakarta, Hotel Amaris Tendean (6.500.000 IDR / participant)
  • Bandung, Hotel Golden Flower (6.500.000 IDR / participant)
  • Bali, Hotel Ibis Kuta (7.500.000 IDR / participant)
  • Lombok, Hotel Jayakarta (7.500.000 IDR / participant)

 

Investasi Pelatihan :

Investasi pelatihan selama tiga hari tersebut menyesuaikan dengan jumlah peserta (on call). *Please feel free to contact us.

Apabila perusahaan membutuhkan paket in house training, anggaran investasi pelatihan dapat menyesuaikan dengan anggaran perusahaan.

 

Fasilitas Pelatihan :

 

  • FREE Airport pickup service (Gratis Antar jemput Hotel/Bandara)
  • FREE Akomodasi Peserta ke tempat pelatihan bagi peserta
  • Module / Handout
  • FREE Flashdisk
  • Sertifikat
  • FREE Bag or bagpackers (Tas Training)
  • Training Kit (Dokumentasi photo, Blocknote, ATK, etc)
  • 2xCoffe Break & 1 Lunch, Dinner
  • FREE Souvenir Exclusive

 

 

 

No Comments

Leave a Reply

Your email address will not be published. Required fields are marked *